View AN2001_1382895.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? motorola inc., 2001 motorola semiconductor application note order this document by: AN2001/d this document contains information on a new product. specifications and information herein are subject to change without notic e. designing expansion boards for the motorola mpc555evb/etas es200 by randy dees rev. 1, 31 july 2001 1 introduction the motorola mpc555evb/etas es200 evaluation board was designed with multiple interfaces to al- low flexibility for expansion. there are three sets of connectors for expansion. the mapi-400+100 is on the bottom side of the board and has access to all signals required to interface to a user application board. the host communication expansion (hce) connectors allow access to the bus of the mpc555. the customized communication expansion (cce) allows access to some of the mpc555 on-chip com- munication ports. the hce and the cce are on the top side of the evb555. 2 the host communication expansion connector (hce) the host communication expansion connectors on the evb555 are designed for use as an expansion of the external bus of the mpc555. they could be used to add additional memory or additional periph- erals. there are two 60-pin connectors (co106 ? a and co107 ? b) part number samtec tfm-130-12- s-d-p. the matching connector required on the expansion board is sfm-130-02-s-d-p. the pin-out of the hce is shown in table 1 . the two connectors are mounted on 1.8 inch (45.72 mm) centers. this allows for a board of approximately three square inches. note an etas etk interface may be mounted above the hce board. the total height (including the connectors on the evb555 and all components on the hce board) must be below 0.6875 inches to allow clearance of the etk board. 2.1 memory chips on the hce all 32 bits of the mpc555 data bus are available on the hce connectors. memory boards designed for these connectors should use all 32 bits for the best performance. on a full-featured board, utilizing memories less than 32 bits wide, the memory can be implemented with multiple chips. for 16-bit wide memories, two chips should be used. provisions should be made on the expansion board to allow the second memory to be disabled to allow for smaller bus widths on the evb555. 16-bit only memories should be connected to d0-d15 of the data bus. cs [2] is available for use on the hce board. if non- volatile memories are used, cs [0] could also be used to allow for booting from the external memory. (it is not possible to boot from the texas instruments tms28f033 on the evb555.) if cs [0] is used, the tms28f033 can be disabled by using the sgf_sel signal on pin 160 of the etk connector (co508). a logic high (default) enables the evb555 on-board external flash memory. in addition, cshce could be used if the chip timing is the same as used by the memory on the evb555 and can fit in a 1-mbyte memory size. f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 2 2.2 peripherals on the hce peripherals can also be added on to the hce bus. chip selects cs [2] and cs [3] are available on the hce connectors. in addition, cshce could be used if the chip timing is the same as used by the mem- ory on the evb555 and can fit in a 1-mbyte memory size. peripherals that could be added include more serial ports, an ethernet adapter, or usb circuitry. table 1 host communication expansion connector a (co106) b (co107) pin name pin name pin name pin name vcc3_3 1 ?? 2 vcc3_3 vcc3_3 1 ?? 2 vcc3_3 vcc[5] 3 ?? 4 vcc[5] vstby3_3 3 ?? 4 vcc5 sdata[31] 5 ?? 6 sdata[30] saddr[31] 5 ?? 6 saddr30 sdata[29] 7 ?? 8 sdata[28] saddr[29] 7 ?? 8 saddr28 sdata[27] 9 ?? 10 sdata[26] saddr[27] 9 ?? 10 saddr26 sdata[25] 11 ?? 12 sdata[24] saddr[25] 11 ?? 12 saddr24 sdata[23] 13 ?? 14 sdata[22] saddr[23] 13 ?? 14 saddr22 sdata[21] 15 ?? 16 sdata[20] saddr[21] 15 ?? 16 saddr20 sdata[19] 17 ?? 18 sdata[18] saddr[19] 17 ?? 18 saddr18 sdata[17] 19 ?? 20 sdata[16] saddr[17] 19 ?? 20 saddr16 sdata[15] 21 ?? 22 sdata[14] saddr[15] 21 ?? 22 saddr14 sdata[13] 23 ?? 24 sdata[12] saddr[13] 23 ?? 24 saddr12 sdata[11] 25 ?? 26 sdata[10] saddr[11] 25 ?? 26 saddr10 sdata[9] 27 ?? 28 sdata[8] saddr[9] 27 ?? 28 saddr8 sdata[7] 29 ?? 30 sdata[6] gnd 29 ?? 30 gnd sdata[5] 31 ?? 32 sdata[4] n/c 31 ?? 32 cshce sdata[3] 33 ?? 34 sdata[2] cs [0] 33 ?? 34 cs1 sdata[1] 35 ?? 36 sdata[0] cs [2] 35 ?? 36 cs3 gnd 37 ?? 38 gnd oe 37 ?? 38 rd/we n/c 39 ?? 40 n/c n/c 39 ?? 40 n/c we /at[0] 41 ?? 42 we /at[1] burst 41 ?? 42 bdip we /at[2] 43 ?? 44 we /at[3] tp113 43 ?? 44 n/c n/c 45 ?? 46 n/c ta 45 ?? 46 tea tsiz1 47 ?? 48 tsiz0 ts 47 ?? 48 bi /sts n/c 49 ?? 50 n/c tp114 49 ?? 50 n/c poreset 51 ?? 52 sreset bb /vf[2]/iwp[3] 51 ?? 52 br /vf[1]/iwp[2] n/c 53 ?? 54 tp108 bg /vf[0]/lwp[1] 53 ?? 54 frz/ptr tp109 55 ?? 56 tp110 clkout 55 ?? 56 tp115 tp111 57 ?? 58 tp112/dis 1 notes: 1. evb555 boards (revision 1.1/1.2) can be modified by connecting pin 58 (tp112) to pin 78 (dis ) of the ti flash (ic400). this allows the ti flash to be disabled and cs [0] to be useable by other devices. tp112 can then be pulled to ground through a 2k ? resistor. in addition, pin 6 of ic403 (/sgeof) should be connected to pin 17 of rn303, a spare pullup resistor, to prevent the floating input of ic403. note : these changes disable the external reset configuration word drivers on the evb555 and may cause limita- tions with the etas etk. tp116 57 ?? 58 tp117 gnd 59 ?? 60 gnd gnd 59 ?? 60 gnd f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 3 2.3 hce board dimensions figure 1 and table 2 show the maximum board dimensions for boards designed to interface to the hce connectors. surface mount components should be used to keep the total height of the hce board and connectors to 0.6875 inches (17.46 mm) to avoid interference with the optional etas etk interface. figure 1 hce board layout 3 the customized communication expansion connectors (cce) the customized communication expansion connectors on the evb555 allows access to the mpc555 on-chip communication ports. the evb555 provides for rs-232 drivers and db9 connector for the sci1 channel of the mpc555. the cce allows for customized connections to all of the mpc555 qsmcm and toucan interfaces. there are two 20-pin connectors (co104 ? a and co105 ? b) part number samtec tfm-110-12-s-d-p. the matching connector required on the expansion board is sfm-110-02-s-d-p. the pin-out of the cce is shown in table 3 . note the txd1 and rxd1 are, by default, connected to the on board rs-232 driver. these can optionally be brought to the txd_cce (7) and rxd_cce (8) pins of connector co105 by changing the position of the 0 ? resistors on br100 and br101 from position 1-2 to position 2-3. table 2 hce board dimensions dimension millimeters inches l 45.72 1.800 s6.350.250 t 44.45 1.75 host communication expansion l s t s f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 4 3.1 cce board dimensions figure 2 and table 4 show the maximum board dimensions for boards that attach the evb555 cce connector. note boards can extend off of the evb for connectors. it is recommended that mounting hardware be supplied to attach the cce board to the evb. figure 2 cce board size table 3 customized communication expansion connector a (co104) b (co105) pin name pin name pin name pin name vcc3_3 1 ?? 2 vcc3_3 vcc3_3 1 ?? 2vcc3_3 vcc5 3 ?? 4 vcc5 vcc5 3 ?? 4 vstby3_3 n/c 5 ?? 6clkout n/c5 ?? 6n/c b_cntx0 7 ?? 8 b_cnrx0 txd_cce 7 ?? 8 rxd_cce tp100 9 ?? 10 tp101 eck 9 ?? 10 tp104 gnd 11 ?? 12 gnd gnd 11 ?? 12 gnd a_cntx0 13 ?? 14 a_cnrx0 tp105 13 ?? 14 tp106 tp102 15 ?? 16 tp103 txd2 15 ?? 16 rxd2 sreset 17 ?? 18 poreset tp107 17 ?? 18 tp118 gnd 19 ?? 20 gnd gnd 19 ?? 20 gnd customized communication expansion m pp n a b u r z (optional) f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 5 4 the mapi-400+100 connectors the mapi-400+100 is an extension of the motorola mapi-400 interface that is used on the motorola mcore products. an additional 100 pin connector was added to support the additional general purpose input/output pins from the port replacement unit of the evb555. note boards designed to interface to mcore mapi-400 boards may not work with the evb555. use of the mapi-400 signals on the evb555 is described in the etas evb555 quick reference guide . table 4 cce board dimensions dimension millimeters inches m 44.45 1.750 n 32.385 1.275 u 6.35 0.25 p6.350.250 r 22.23 0.875 z12.70.50 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 6 figure 3 mapi-400+100 footprint 1 2 99 100 j5(c0604) 1 2 99 100 j2(c0601) 1 2 99 100 j3(c0602) 1 2 99 100 j1(c0600) 1 2 99 100 j4(c0603) mpc555 top view primary datum 4 x ?m h j k l f g 0.0 a b c d 0.0 e f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 7 table 5 mapi-400+100 dimensions dimension millimeters inches a 91.45 3.60 b 83.82 3.300 c 45.72 1.800 d7.620.300 e 14.22 0.560 f 31.78 1.250 g 10.16 0.400 h 58.42 2.300 j 104.14 4.100 k 111.76 4.400 l 127.00 5.000 m3.200.126 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 8 table 6 mapi-400 signal definitions j1 (co600) j2 (co601) pin name pin name p in name pin name aan[51]/pqb[7] 1 ?? 21 ?? 2 aan50_pqb6 aan[52]/pqa[0] 3 ?? 43 ?? 4 aan49_pqb5 aan[53]/pqa[1] 5 ?? 65 ?? 6 aan48_pqb4 aan[54]/pqa[2] 7 ?? 87 ?? 8 aan3_pqb3 aan[55]/pqa[3] 9 ?? 10 9 ?? 10 aan2_pqb2 aan[56]/pqa[4] 11 ?? 12 11 ?? 12 aan1_pqb1 aan[57]/pqa[5] 13 ?? 14 13 ?? 14 aan0_pqb0 aan[58]/pqa[6] 15 ?? 16 15 ?? 16 aan[59]/pqa[7] 17 ?? 18 ground 17 ?? 18 ground 19 ?? 20 19 ?? 20 21 ?? 22 mda11 21 ?? 22 mda12 23 ?? 24 mda13 23 ?? 24 mda14 25 ?? 26 mda15 25 ?? 26 mda27 a_tpuch[0] 27 ?? 28 ground mda28 27 ?? 28 mda29 a_tpuch[1] 29 ?? 30 mpwm[0] 29 ?? 30 hresetb a_tpuch[2] 31 ?? 32 mpwm[1] etrig1 31 ?? 32 extclk a_tpuch[3] 33 ?? 34 etrig2 33 ?? 34 bbb_iwp3 a_tpuch[4] 35 ?? 36 mpwm[2] bdip 35 ?? 36 bgb_lwp1 a_tpuch[5] 37 ?? 38 mpwm[3] bib_stsb 37 ?? 38 brb_iwp2 a_tpuch[6] 39 ?? 40 burstb 39 ?? 40 sgp_irqoutb ground 41 ?? 42 mpwm[16] tsb 41 ?? 42 epee a_tpuch[7] 43 ?? 44 mpwm[17] ground 43 ?? 44 a_tpuch[8] 45 ?? 46 ground 45 ?? 46 ground a_tpuch[9] 47 ?? 48 mpwm[18] eck 47 ?? 48 engclk/buclk a_tpuch[10] 49 ?? 50 mpwm[19] rxd1_qgpi 49 ?? 50 txd1_qgpo a_tpuch[11] 51 ?? 52 rxd2_qgpi 51 ?? 52 txd2_qgpo a_tpuch[12] 53 ?? 54 a_tpuch[15] 53 ?? 54 a_tpuch[13] 55 ?? 56 a_t2clk 55 ?? 56 a_tpuch[14] 57 ?? 58 57 ?? 58 59 ?? 60 59 ?? 60 irq [1]/sgp 61 ?? 62 irq [0]/sgp mda30 61 ?? 62 irq [3]/sgp 63 ?? 64 irq [2]/sgp ground 63 ?? 64 ground irq [5]/sgp 65 ?? 66 irq [4]/sgp mda31 65 ?? 66 mpio5 irq [7]/mck3 67 ?? 68 irq [6]/mck2 mpio6 67 ?? 68 mpio7 69 ?? 70 mpio8 69 ?? 70 mpio9 ground 71 ?? 72 mpio10 71 ?? 72 mpio11 73 ?? 74 ground mpio12 73 ?? 74 mpio13 75 ?? 76 mpio14 75 ?? 76 mpio15 77 ?? 78 77 ?? 78 79 ?? 80 79 ?? 80 81 ?? 82 81 ?? 82 83 ?? 84 ground 83 ?? 84 ground 85 ?? 86 85 ?? 86 87 ?? 88 87 ?? 88 ban0_pqb0 ground 89 ?? 90 89 ?? 90 ban1_pqb1 91 ?? 92 ground 91 ?? 92 ban2_pqb2 93 ?? 94 93 ?? 94 ban3_pqb3 95 ?? 96 95 ?? 96 ban48_pqb4 97 ?? 98 97 ?? 98 ban49_pqb5 99 ?? 100 vpp 99 ?? 100 ban50_pqb6 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 9 table 7 mapi-400 signal definitions j3 (co602) j4 (co603) pin name pin name pin name pin name 1 ?? 2 ban51_pqb7 1 ?? 2 3 ?? 4 ban52_pqa0 data_sgp1 3 ?? 4 data_sgp0 5 ?? 6 ban53_pqa1 data_sgp3 5 ?? 6 data_sgp2 7 ?? 8 ban54_pqa2 data_sgp5 7 ?? 8 data_sgp4 9 ?? 10 ban55_pqa3 data_sgp7 9 ?? 10 data_sgp6 11 ?? 12 ban56_pqa4 data_sgp9 11 ?? 12 data_sgp8 13 ?? 14 ban57_pqa5 data_sgp11 13 ?? 14 data_sgp10 15 ?? 16 ban58_pqa6 ground 15 ?? 16 ground 17 ?? 18 ban59_pqa7 data_sgp13 17 ?? 18 data_sgp12 19 ?? 20 data_sgp15 19 ?? 20 data_sgp14 21 ?? 22 data_sgp17 21 ?? 22 data_sgp16 23 ?? 24 data_sgp19 23 ?? 24 data_sgp18 ground 25 ?? 26 b_tpuch0 data_sgp21 25 ?? 26 data_sgp20 a_cnrx0 27 ?? 28 b_tpuch1 ground 27 ?? 28 ground a_cntx0 29 ?? 30 b_tpuch2 data_sgp23 29 ?? 30 data_sgp22 31 ?? 32 b_tpuch3 data_sgp25 31 ?? 32 data_sgp24 b_cnrx0 33 ?? 34 b_tpuch4 data_sgp27 33 ?? 34 data_sgp26 b_cntx0 35 ?? 36 b_tpuch5 data_sgp29 35 ?? 36 data_sgp28 37 ?? 38 b_tpuch6 data_sgp31 37 ?? 38 data_sgp30 sck_qgp6 39 ?? 40 b_tpuch7 ground 39 ?? 40 ground miso_qgp4 41 ?? 42 b_tpuch8 41 ?? 42 ground 43 ?? 44 b_tpuch9 43 ?? 44 mosi_qgp5 45 ?? 46 b_tpuch10 45 ?? 46 pcs0_qgp 47 ?? 48 b_tpuch11 47 ?? 48 49 ?? 50 b_tpuch12 addr_sgp9 49 ?? 50 addr_sgp8 pcs1qgp 51 ?? 52 b_tpuch13 addr_sgp11 51 ?? 52 addr_sgp10 pcs2qgp 53 ?? 54 b_tpuch14 addr_sgp13 53 ?? 54 addr_sgp12 55 ?? 56 b_tpuch15 addr_sgp15 55 ?? 56 addr_sgp14 pcs3qgp 57 ?? 58 b_t2clk ground 57 ?? 58 ground 59 ?? 60 addr_sgp17 59 ?? 60 addr_sgp16 61 ?? 62 vf0_mpio0 addr_sgp19 61 ?? 62 addr_sgp18 63 ?? 64 vf1_mpio1 addr_sgp21 63 ?? 64 addr_sgp20 ground 65 ?? 66 vf2_mpio2 addr_sgp23 65 ?? 66 addr_sgp22 vfls0_mpio3 67 ?? 68 ground addr_sgp25 67 ?? 68 addr_sgp24 vfls1_mpio4 69 ?? 70 addr_sgp27 69 ?? 70 addr_sgp26 iwp0_vfls 71 ?? 72 addr_sgp29 71 ?? 72 addr_sgp28 iwp1_vfls 73 ?? 74 addr_sgp31 73 ?? 74 addr_sgp30 75 ?? 76 ground 75 ?? 76 ground poresetb 77 ?? 78 tab 77 ?? 78 teab 79 ?? 80 tdo_dsdo 79 ?? 80 web_at[0] ground 81 ?? 82 tdi_dsdi rd_wrb 81 ?? 82 web_at[1] tms 83 ?? 84 ground 83 ?? 84 web_at[2] tck_dsck 85 ?? 86 tsiz0 cs0b 85 ??86 web_at[3] trst_b 87 ?? 88 tsiz1 cs1b 87 ??88 oeb sreset 89 ?? 90 rstconf/texp cs2b 89 ??90 ground 91 ?? 92 cs3b 91 ??92 93 ?? 94 frz_ptr ground 93 ??94 ground 95 ?? 96 clkout 95 ??96 ground ground 97 ?? 98 ground 97 ??98 99 ?? 100 99 ? ? 100 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 10 table 8 mapi-400 +100 pru extended signal definitions j5 (co605) pin name pin name b_pio0 1 ?? 2a_pio0 b_pio1 3 ?? 4a_pio1 b_pio2 5 ?? 6a_pio2 b_pio3 7 ?? 8a_pio3 b_pio4 9 ?? 10 a_pio4 b_pio5 11 ?? 12 a_pio5 b_pio6 13 ?? 14 a_pio6 ground 15 ?? 16 ground b_pio7 17 ?? 18 a_pio7 b_pio8 19 ?? 20 a_pio8 b_pio9 21 ?? 22 a_pio9 b_pio10 23 ?? 24 a_pio10 b_pio11 25 ?? 26 a_pio11 ground 27 ?? 28 ground b_pio12 29 ?? 30 a_pio12 b_pio13 31 ?? 32 a_pio13 b_pio14 33 ?? 34 a_pio14 b_pio15 35 ?? 36 a_pio15 b_pio16 37 ?? 38 a_pio16 ground 39 ?? 40 ground b_pio17 41 ?? 42 a_pio17 b_pio18 43 ?? 44 a_pio18 b_pio19 45 ?? 46 a_pio19 b_pio20 47 ?? 48 a_pio20 b_pio21 49 ?? 50 a_pio21 b_pio22 51 ?? 52 a_pio22 b_pio23 53 ?? 54 a_pio23 b_pio24 55 ?? 56 a_pio24 ground 57 ?? 58 ground b_pio25 59 ?? 60 a_pio25 b_pio26 61 ?? 62 a_pio26 b_pio27 63 ?? 64 a_pio27 b_pio28 65 ?? 66 a_pio28 b_pio29 67 ?? 68 a_pio29 b_pio30 69 ?? 70 a_pio30 b_pio31 71 ?? 72 a_pio31 73 ?? 74 ground 75 ?? 76 ground 77 ?? 78 79 ?? 80 81 ?? 82 ground 83 ?? 84 /extbus 85 ?? 86 standby 87 ?? 88 ground 89 ?? 90 ground ground 91 ?? 92 ground ground 93 ?? 94 ground ub2 95 ?? 96 ub2 ub2 97 ?? 98 ub2 ub2 99 ?? 100 ub2 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 11 5 lauterbach trace connector the mpc555evb includes a 64-pin connector to allow trace tools, such as lauterbach?s trace-32, a simple connection to the signals required for trace. table 9 lauterbach universal mpc500/800 family trace adapter connector co500 pin name pin name addr20 1 ?? 2 addr21 addr11 3 ?? 4 addr22 addr19 5 ?? 6 addr23 addr18 7 ?? 8 addr24 addr17 9 ?? 10 addr12 data11 11 ?? 12 addr13 rd_wr 13 ?? 14 addr14 data8 15 ?? 16 addr15 vcc3_3 17 ?? 18 addr16 data3 19 ?? 20 we _at2 data2 21 ?? 22 irqout_lwp0 data1 23 ?? 24 we _at3 data0 25 ?? 26 br _vf1_iwp2 vcc5 27 ?? 28 data10 we _at0 29 ?? 30 data9 gnd 31 ?? 32 iwp0_vfls0 clkout 33 ?? 34 iwp1_vfls1 we _at1 35 ?? 36 bg _vf0_lwp1 data7 37 ?? 38 bb _vf2_lwp3 data6 39 ?? 40 addr10 data5 41 ?? 42 addr9 gnd 43 ?? 44 addr8 data4 45 ?? 46 bi _sts addr26 47 ?? 48 ts addr29 49 ?? 50 frz _ptr addr30 51 ?? 52 vfls0_mpio3 addr27 53 ?? 54 vfls1_mpio4 addr31 55 ?? 56 vf1_mpio1 addr28 57 ?? 58 vf0_mpio0 addr25 59 ?? 60 vf2_mpio2 rstconf 61 ?? 62 irq3 _kr hreset 63 ?? 64 irq4 _at2 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 12 6 mounting holes figure 4 shows the mounting holes available to mount the evb555 to other boards. table 10 shows the dimensions of the connectors on the top side of the board. figure 4 mounting holes and top-side connector dimensions b m n a a b j h customized communication expansion l host expansion communication mpc555 g f 8 x ? k e c a top view 0.0 d u b w y 0.0 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 13 7 keep-out areas all of the connectors on the top side of the evb555 have keep-out areas associated with them to ac- commodate any board that could be connected to the expansion connectors. figure 5 shows the vari- ous keep-out areas. table 10 top dimensions dimension millimeters inches a 120.00 4.724 b 115.19 4.535 c 79.63 3.135 d 39.63 1.560 e4.700.185 f 13.34 0.525 g 29.22 1.150 h 182.89 7.200 j 200.00 7.874 k2.800.110 l 45.72 1.800 m 44.45 1.750 n 32.385 1.275 u6.350.250 w 32.39 1.275 y 66.675 2.625 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 14 figure 5 expansion board keep-out areas etk keep-out area hce, cce, keep-out areas lauterbach f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 15 8 summary of connectors table 11 shows the number and types of each kind of user extension connectors on the evb555. shown are the part numbers for the connectors on the evb555 and the part numbers for connectors that are required for a user board. 9 reference for more information see the following reference material. 9.1 mpc555 user?s manual the mpc555 user?s manual (mpc555um/ad) is available from motorola and describes the mpc555 device. the url for the motorola website is http://www.mcu.motsps.com/lit/mpc.html . 9.2 evb555 mpc555 evaluation board quick reference, etas 9.3 samtec connectors samtec has board layout recommendations and specifications for all of their connectors available on- line. the url for this website is http://www.samtec.com. 9.4 robinson nugent connector further information on the robinson nugent connectors is available on-line. the url for this website is http://www.robinsonnugent.com. at that site, search for p50l connectors. table 11 summary of connectors connector number of connectors on board evb555 connector part number user board connector part number (surface mount) user board connector part number (through hole) co100 background debug mode interface 1 each 3m 925320-01-10-10 3m 8510-4500 jl (board mount) 3m chg-2010-j01010-kcp (wire mount) co104/co105 customized communication expansion 2 each samtec tfm-110-12-s-d-p samtec sfm-110-02-s-d-p co106/co107 host communication expansion 2 each samtec tfm-130-12-s-d-p samtec sfm-130-02-s-d-p co500-505 mictor digital logic analyzer 6 each amp 767 004 product code 2429 co506/co507 analog logic analyzer 2 each 3m 925320-01-20-10 3m 8520-4500 (board mount) 3m chg-2020-j01010-kcp (wire mount) co509 lauterbach interface 1 each samtec fte-132-02-g-dv-p samtec cle-132-01-g-dv-p co600-604 mapi-400+100 5 each robinson nugent p50l-100 s-bs-tgf robinson nugent p50l-100 p-as-tgf f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 16 9.5 lauterbach more information on the lauterbach real-time trace module is available on-line. the url for this web- site is http://www.lauterbach.de . 10 revision history table 12 revision history release number date author sections affected summary of changes 1 31 july 01 randy dees table 5 added dimension a to table 5 . re- named dimension i in table 5 to agree with figure 3 . f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 17 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 18 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
designing expansion boards for the motorola mpc555evb/etas es2000 motorola rev. 1, 31 july 2001 19 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .
motorola reserves the right to make changes without further not ice to any products herein. motorola makes no warranty, represen tation or guarantee regarding the suitability of its products for any particular purpose, nor does motorola assume any liability arising out of the applicati on or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. ?typical? param eters can and do vary in different applications. all operating parameters, including ?typicals? must be validated for each customer application by customer?s tech nical experts. motorola does not convey any license under its patent rights nor the rights of others. motorola products are not designed, intended, or authorize d for use as components in systems intended for surgical implant into the body, or other applicati ons intended to support or sustain life, or for any other applic ation in which the failure of the motorola product could create a situation where personal injury or death may occur. should buyer purchase or use motorola products for a ny such unintended or unauthorized application, buyer shall indemnify and hold motorola and its officers, employees, subsidiaries, affiliates, and di stributors harmless against all claims, costs, damages, and expenses, and reasonable attor ney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that moto rola was negligent regarding the design or manufacture of t he part. motorola is a registered trademark of motorola, inc. motorola, inc. is an equal opportunity/affirmative action employer. to obtain additional product information: usa/europe: motorola literature distribution; p.o. box 20912; phoenix, arizona 85036. 1-800-441-2447 japan: nippon motorola ltd.; tatsumi-spd-jldc, toshikatsu otsuki, 6f seibu-butsuryu-center, 3-14-2 tatsumi koto-ku, tokyo 135, japan. 03-3521-8315 hong kong: motorola semiconductors h.k. ltd.; 8b tai ping industrial park, 51 ting kok road, tai po, n.t., hong kong. 852-26629298 mfax: rmfax0@email.sps.mot.com - touchtone (602) 244-6609 internet: http://www.mot.com AN2001 f r e e s c a l e s e m i c o n d u c t o r , i freescale semiconductor, inc. f o r m o r e i n f o r m a t i o n o n t h i s p r o d u c t , g o t o : w w w . f r e e s c a l e . c o m n c . . .

▲Up To Search▲

Price & Availability of AN2001

	To Download AN2001 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .